Installing the panel on your own server
SelyaThe panel is installed with one command on an ordinary server. You do not need to enter the subscription key, it gets into the panel by itself. You need only a server and five minutes.
The Sellerist panel runs on your own server, not on ours. So all your marketplace keys, orders and conversations lie only with you. It is installed with one command, which the page shows after payment.
What you need
| What | Which |
|---|---|
| System | A clean Ubuntu 22.04 or 24.04. It may work on another Debian-like system, but we tested these two |
| Memory | 2 GB or more. With 1 GB it starts, but barely |
| Disk | 10 GB or more. The installer refuses if less than 2.5 GB is free, and updates need room for the new image |
| Processor | 64-bit x86 (an ordinary virtual machine). Raspberry Pi and ARM servers do not fit |
| Ports | 80 and 443 free. If nginx or Apache is already on the server, take another server |
Any hosting that sells virtual servers (VPS) will do. Telegram is often blocked on Russian addresses, and the panel sends notifications about orders and messages to it. If that matters to you, take a server abroad.
Step 1. Sign in to the server over SSH
The hosting sends you the server's address (IP), a login (usually root) and a password. On Windows 10 and 11 open PowerShell, on a Mac open Terminal, and type:
ssh root@server-addressWhen asked about the fingerprint, answer yes, then enter the password. The password is not shown as you type, that is normal.
Step 2. Paste the command
The command looks like this; your own link is on the page after payment:
curl -fsSL https://hub.sellerist.ru/i/YOUR-LINK | sudo bashIf you already have a domain for the panel (for example panel.example.com) and its A record points to the server's IP, enter the domain in the field on the payment page, and the command will include it. By hand it looks like this:
curl -fsSL https://hub.sellerist.ru/i/YOUR-LINK | sudo bash -s -- --domain panel.example.comAfter that the command does everything itself, which takes a few minutes: it checks the server, downloads the panel (about 400 MB), verifies the signature, installs Docker, starts the panel and enters your subscription key into it.
Step 3. Save the password and sign in
At the end the installer prints the panel's address, a login and a password. The password is shown once. Save it in a password manager at once. If you lose it, it can be reset with a command on the server, but it is easier to write it down right away.
Open the address in a browser, sign in and connect your marketplaces: the panel leads you through the steps.
A domain and HTTPS
With a domain the panel gets a certificate by itself, and passwords travel over the network encrypted. Without a domain the panel opens at an address like http://server-IP, with no encryption. That will do to start, but it is better to add a domain: buy one, create an A record to the server's IP and run the install with --domain.
If the install stopped
Just run the same command again. What was downloaded is not downloaded again, and the password and data are kept. The command is valid for 7 days and works until the install finishes successfully.
| What it says | What to do |
|---|---|
| Less than 2.5 GB free on the disk | Take a server with a disk of 10 GB or more, or free up room (apt clean, docker image prune) |
| Port 80 or 443 is busy | Stop the program that holds it, or take a clean server |
| The install link does not work | 7 days have passed, the install was already finished, or it was downloaded three times. The bot @sellerist_extension_bot will send a new command on /install |
| The release signature does not match | The install is stopped, nothing is installed. Run the command again, and if it repeats, write to support |
| OpenSSL 3 is needed | The system is older than Ubuntu 22.04. Take 22.04 or 24.04 |
What about the subscription key
The command has no key in it, so it does not stay in the terminal history. The installer gets it from us by your link and writes it into the panel's settings. The payment page shows the key for 24 hours. If you installed the panel later, open Settings → Subscription in it and enter the key by hand. You can send the key to yourself in Telegram with a button on the payment page.
Updates
When a new version comes out, the panel shows it in Settings (the “Updates” card), and the Update button does everything itself. An update also needs free disk space, which is why we advise a disk of 10 GB or more.